Closed Search Tips

Search is based on keyword.

Ex: "Procedures"

Do not search with natural language

Ex: "How do I write a new procedure?"

Using Curves with MeshFusion

Curves, Beziers, and B-Splines can serve as input meshes in MeshFusion modeling. They can be used the same way as regular polygonal meshes and produce primaries, trims, and surface strips.

B-Splines are native to MeshFusion, but Curves and Beziers are automatically converted to B-Splines when used by MeshFusion. Bezier curves can only be converted to B-Spline approximately, but you can increase the number of B-Spline segments for greater accuracy.

MeshFusion works with open, closed, flat, and 3D curves. You can also use curves produced by the Text tool with the Bezier Output Type.

Using a Curve as an Input Mesh

To use a Curve as an input mesh, make sure you have a scene containing a mesh item in one layer and a curve in another mesh layer.

Note:  For more information on adding different types of curves, see Curve, Bezier, or B-Spline.

1.   Select your mesh item in the Item List, and create a new fusion item, as described in Creating a New Fusion Item.

Your mesh item becomes a primary and it's marked with green in the Item List and the 3D viewport. A Fusion Item is also created.

2.   In the Item List, select the mesh layer containing your curve, and the mesh layer containing your primary.
3.   In the Fusion sub-tab on the left panel, click the required button, depending on the kind of trim or surface strip you want to create. For example, to create the surface strip example below, click the Full Strip with Grid Crossing button under Apply Surface Strip.

For more information on mesh roles and surface strips, see Mesh Roles and Relationships, and Fusion Surface Strips.

This example shows a curve applied to one of the Fusion Qbic Presets first as a Subtractive Trim, then as a Surface Strip.

Original

Subtractive Trim

Surface Strip

Curve Input Properties

The Curve input settings help you adjust how your curve is converted to B-Spline and how geometry is extruded during MeshFusion. To access them:

1.   Select your curve in the Item List.

This opens the Properties tab on the lower right panel.

2.   In the Mesh sub-tab, scroll down to the Mesh Fusion Curve Input section.

Manual Extrusion Depth

When enabled, you can specify the Extrusion Depth value. When disabled, Modo uses the default.

Extrusion Depth

Specifies how far meshes are extruded from the curves when Manual Extrusion Depth is enabled.

Extrude Direction

Specifies the way meshes are extruded. The options are:

• Extrude Perpendicular to Curve - The surface is extruded perpendicular to the plane of the curve, to a specified distance. This works well if the curve is flat, that is, it doesn't deviate from a plane.

• Extrude Along Surface Normal - The curve is treated as a 3D curve and the surface produced from it is used as a trim. The cutting surface is extruded in the direction perpendicular to the surface being cut. This works for creating a surface strip on any curved surface by laying down the curve on that surface using the Mesh Constraints tools.

Segment Count

Specifies the number of B-Spline segments used when converting Bezier curves to B-Spline. Bezier curves can only be converted to B-spline approximately. The greater the number of B-Spline control points, the closer the approximation. Increasing the number of B-spline segments provides greater accuracy, but too many segments can reduce performance and increase output mesh density.

For smooth Bezier curves without sharp angles, even a limited number of B-Spline segments is enough.

Bezier Corner Angle

The corners on a Bezier curve are automatically rounded when it's converted to a B-Spline. This specifies a threshold for rounding corners. Only the sharp corners where the change in direction is significant enough are rounded. Shallower corners are rounded by a very smooth curve, essentially becoming non-corners.

Bezier Corner Roundness

This value specifies the strength of the rounding effect.